Published: 2025-05-19

RESEARCH ARTICLES

Performance Assessment of Solar Air Heater Channel with Inclined Groove Turbulators

N. Koolnapadol, P. Promvonge, C. Khanoknaiyakarn, P. Promthaisong, P. Hoonpong, A. Chaimanatsakun, S. Gururatana, S. Skullong

JRAME-25-13-016 (p.1-11)

PDF

Combustion Characteristics of Liquefied Petroleum Gas with Ammonia addition on Slot Burner

T. Sudjan, S. Jugjai, A. Kaewpradap

JRAME-25-13-017 (p.1-8)

PDF

Numerical Simulation of Harmonic Gust Induced 2D Low-Re Incompressible Flow Over Tandem Circular Cylinders using ECFRUNS

Y. A. Joshi, R. Bhoraniya, A. B. Harichandan

JRAME-25-13-018 (p.1-16)

PDF

Soft Pneumatic Actuator Designed After Human Finger Motion

N. Gariya, H. Singh, S. Chamoli, A. Shaikh, A.S. Dwivedi, P. Baranwal

JRAME-25-13-019 (p.1-9)

PDF

Predicting Performance and Emission Characteristics of Compression Ignition Engine Using Artificial Neural Network with Biodiesel Blends from Used Temple Oil

S. B. Anjappa, D. K. Ramesha, K. Ganesh, B. C. Channakeshava

JRAME-25-13-020 (p.1-17)

PDF

Nonlinear Vibration Analysis of Phased-controlled Actuator Capable of Movement inside Iron Structures

H. Yaguchi, R. Sato

JRAME-25-13-021 (p.1-16)

PDF

Enhancing Combustion Analysis: Implementation and Validation of Laminar Premixed Methane-Air Jet-Impinging Flame Simulation in OpenFOAM

P. Kamma, K. Loksupapaiboon, J. Phromjan, C. Suvanjumrat

JRAME-25-13-022 (p.1-12)

PDF

Numerical Study of Anthracite Blended with Petroleum Coke on Swirl-JET Burner in Cement Kiln

A. Kaewpradap, J. Charoensuk, C. Chantang

JRAME-25-13-023 (p.1-12)

PDF

Development of the Cooling Load Calculation Program Using MATLAB as a Stand-Alone Application

A. Pramuanjaroenkij, P. Onnog, P. Janthasri, A. Tongkratoke, S. Phankhoksoong, C. Chungchoo

JRAME-25-13-024 (p.1-14)

PDF

Computational Fluid Dynamics Analysis for Heat Transfer Enhancement in Single Horizontal Pipe Heat Exchanger Full Filled Using Different Types of Porous Material

S. A. Ali, M. R. Hameed

JRAME-25-13-025 (p.1-11)

PDF

Exploring Mechanical Properties of Additive Manufactured Patient-Specific Finger Splints through FEA and Experimental Testing

S. M. Kennedy, K. Amudhan, R.B. Jeen Robert, A. Vignesh Moorthy Pandian

JRAME-25-13-026 (p.1-12)

PDF

Numerical Investigation of the Greenhouse with the Floor and Other Cooling Systems

U. Srangtham , A. Pramuanjaroenkij, P. Janthasri, S. Dokkaew, S. Kakac, A. Tongkratoke

JRAME-25-13-027 (p.1-15)

PDF

Influence of Delta Winglets on Improving heat transfer and friction factor characteristics in tubular heat exchanger

K. Ruengpayungsak, P. Samruaisin, P. Kaewkosum, S. Pingta, K. Wongcharee, A. Phila, S. Eiamsa-ard, P. Thapmanee

JRAME-25-13-028 (p.1-15)

PDF

Leveraging Generative Artificial Intelligence for Prototyping: Ambidextrous Thinking in Engineering Design

K. Miura, D. Misaki

JRAME-25-13-029 (p.1-10)

PDF

Impact of Battery Pack Shell Materials on Electrical Leakage in Submersion

D.N. Ngo, C. Charoenphonphanich, N. Kunanusont, P. Meelapchotipong, C.T. Vo, T.S.V. Pham, M. Masomtob

JRAME-25-13-030 (p.1-11)

PDF

The Air Distribution Simulation inside the Glass Showroom Using Radiant Floor and Convection Cooling Systems

A. Pramuanjaroenkij, S. Dokkaew, P. Janthasri, A. Tongkratoke

JRAME-25-13-031 (p.1-13)

PDF