Journal of Research and Applications in Mechanical Engineering

Journal Abbreviation: J. Res. Appl. Mech. Eng.
ISSN: 2229-2152 (Print)
ISSN: 2697-424x (Online)
Language: English
Publication fee: free of charge
Issues per years: 3 Issues (1st issue: January - April /2nd issue: May - August/3rd issue: September-December)
Review Method: Double-blind review

          

The Journal of Research and Applications in Mechanical Engineering (JRAME) publishes results of research, applications, ideas and innovations related to mechanical engineering issues. Manuscripts submitted to the journal must be (1) original, (2) substantial, and (3) of significant importance.

JRAME, a peer-reviewed journal, aims to provide the most complete and reliable source of information on current developments in the field. Emphasis will be on rapidly publishing quality manuscripts that are freely available to researchers worldwide.

All manuscripts submitted to JRAME undergo a peer-review process via a double-blind review. Normally, two or three reviewers are invited to comment on a manuscript. Authors may request that certain reviewers not be used, but this decision should be left to Editor's discretion.

Vol. 13 No. 2 (2025)

Published: 2025-05-19

Performance Assessment of Solar Air Heater Channel with Inclined Groove Turbulators

N. Koolnapadol, P. Promvonge, C. Khanoknaiyakarn, P. Promthaisong, P. Hoonpong, A. Chaimanatsakun, S. Gururatana, S. Skullong

JRAME-25-13-016 (p.1-11)

Soft Pneumatic Actuator Designed After Human Finger Motion

N. Gariya, H. Singh, S. Chamoli, A. Shaikh, A.S. Dwivedi, P. Baranwal

JRAME-25-13-019 (p.1-9)

Numerical Study of Anthracite Blended with Petroleum Coke on Swirl-JET Burner in Cement Kiln

A. Kaewpradap, J. Charoensuk, C. Chantang

JRAME-25-13-023 (p.1-12)

Development of the Cooling Load Calculation Program Using MATLAB as a Stand-Alone Application

A. Pramuanjaroenkij, P. Onnog, P. Janthasri, A. Tongkratoke, S. Phankhoksoong, C. Chungchoo

JRAME-25-13-024 (p.1-14)

Exploring Mechanical Properties of Additive Manufactured Patient-Specific Finger Splints through FEA and Experimental Testing

S. M. Kennedy, K. Amudhan, R.B. Jeen Robert, A. Vignesh Moorthy Pandian

JRAME-25-13-026 (p.1-12)

Numerical Investigation of the Greenhouse with the Floor and Other Cooling Systems

U. Srangtham , A. Pramuanjaroenkij, P. Janthasri, S. Dokkaew, S. Kakac, A. Tongkratoke

JRAME-25-13-027 (p.1-15)

Influence of Delta Winglets on Improving heat transfer and friction factor characteristics in tubular heat exchanger

K. Ruengpayungsak, P. Samruaisin, P. Kaewkosum, S. Pingta, K. Wongcharee, A. Phila, S. Eiamsa-ard, P. Thapmanee

JRAME-25-13-028 (p.1-15)

Impact of Battery Pack Shell Materials on Electrical Leakage in Submersion

D.N. Ngo, C. Charoenphonphanich, N. Kunanusont, P. Meelapchotipong, C.T. Vo, T.S.V. Pham, M. Masomtob

JRAME-25-13-030 (p.1-11)

The Air Distribution Simulation inside the Glass Showroom Using Radiant Floor and Convection Cooling Systems

A. Pramuanjaroenkij, S. Dokkaew, P. Janthasri, A. Tongkratoke

JRAME-25-13-031 (p.1-13)

View All Issues