Influence of Parameter in Rubber-Wood Full-Cell Preservation Process

Authors

  • ภาณุ คำกรฤาชา
  • อภิชาติ อาจนาเสียว

Keywords:

Rubber Wood, Full-Cell Process, Disodium Octaborate Tetra hydrate, Wood Preservation

Abstract

      This research studied influences on penetration and retention of disodium octaborate tetra hydrate in Full-Cell process. The conditions of experiment were held 0.2 bar vacuum pressure, applied 8, 10, 12 bar pressure and hold 0/60, 10/50, 20/40 (min/min) vacuum/pressure time. The results show that, 10 bar pressure and time 0/60 give the highest %BAE (boric acid equivalent) results about 1.11, 14.82 ppm. Compare with wood standard from factory witch boron concentration was 1.982 ppm. When time condition were 0/60 to 20/40, provide a decreasing trend of boron retention .When time condition were 0/60 and pressure increased from 8 bar to 10 bar pressure, provide an increasing trend of boron retention. When the pressure was raised from 10 bar to 12 bar pressure, provide a decreasing trend of boron retention

References

[1] W.Sittichaya and R.Beaver, “Rubberwood destroying beetles in the eastern and gulf areas of Thailand (Coleoptera: Bostrichidae, Curculionidae: Scolytinae and Platypodinae),” Songklanakarin Journal of Science and Technology, 2009.
[2] UM.Abeysinghe and HS.Amarasekera, “Pressure and non- pressure preservation methods for rubber wood treatment by Boron preservatives,” Proc Int for Environ Symp, 16, 2011.
[3] TK.Dhamodaran, “Preservative Treatment and Chemical Modification of Rubber wood,” Kerala Forest Research Institute, 1996.
[4] O.Sulaiman, “The effect of relative humidity on the physical and mechanical properties of oil palm trunk and rubberwood,” Cellul Chem Technol. 2012, 46(5), 401–7.
[5] ASTM International, “ASTM D4442 – 92 (2003), Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials,” 1992.
[6] Bureau of Indian Standards, “IS 2753-1 (1991): Methods for estimation of preservatives in treated timber and in treating solutions, Part 1: Determination of copper, arsenic, chromium, zinc, boron, creosote and fuel oil,” CED 9, Timber and
Timber Stores, 1991.
[7] Ministry of Industry Thailand, "TIS industrial standards, 1894-2009," 2009.
[8] American Wood Preservers’ Association, “AWPAA7, Standard for wet ashing procedures for preparing wood for chemical analysis,” 2012.
[9] American Wood Preservers’ Association, “AWPAA11: Standard Method for Analysis of Treated Wood and Treating Solutions by Atomic Absorption Spectroscopy,”1983.
[10] J.D. MacLean, “Preservative pressure. In: preservative treatment of wood by pressure methods,” Agriculture handbook No40. U.S. Govt. print. Off., 1953.

Downloads

Published

2020-06-22

How to Cite

[1]
คำกรฤาชา ภ. . . and อาจนาเสียว อ. . ., “Influence of Parameter in Rubber-Wood Full-Cell Preservation Process”, Eng. & Technol. Horiz., vol. 34, no. 2, pp. 50–55, Jun. 2020.

Issue

Vol. 34 No. 2 (2017): April -June

Section

Research Articles

License

The published articles are copyrighted by the School of Engineering, King Mongkut's Institute of Technology Ladkrabang.

The statements contained in each article in this academic journal are the personal opinions of each author and are not related to King Mongkut's Institute of Technology Ladkrabang and other faculty members in the institute.
Responsibility for all elements of each article belongs to each author; If there are any mistakes, each author is solely responsible for his own articles.