Parametric study on contribution of combined confining steel and steel fiber to column’s displacement ductility
Article Sidebar
Main Article Content
Abstract
This study examines the contribution of confinement with variations in spacing sh = (50, 65, and 80) mm and concrete reinforced with steel fiber to displacement ductility. Eight test column specimens (No. 1, 2, 3, 6, 7, 8, 11, and 12) were also reinforced with stirrups according to ACI 318M:19 provisions while four test column specimens (No. 4, 5, 9, and 10) deliberately reinforced with a slightly wider spacing of stirrups with different yield strengths (fy) (lower than the code requirements). However, the volumetric ratio of the steel fiber was varied, i.e. Vf = 0%, 0.5%, 1%, 1.5%, and 2%. The column was then subjected to a quasi-cyclic and a constant axial load of Pa = 0.121.Ag.fc'. The test results indicated that all test column specimens could attain the full ductile/fully ductile criteria since mD>4. When the drift ratio required by ACI 318M-19 is observed, the use of combined confining stirrups and steel fiber works together simultaneously to achieve a drift ratio capacity that exceeds the minimum required target of 3%, meaning that the columns could perform satisfactorily.
Article Details
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
References
Anggraini R, Tavio, Raka IGP, Agustiar. Experimental load-drift relations of concrete beam reinforced and confined with high-strength steel bars under reversed cyclic loading. ASEAN Eng J. 2021;11(4):56-69.
Anggraini R, Tavio, Raka IGP, Agustiar. Flexural capacity of concrete beams reinforced with high-strength steel bars under monotonic loading. Int J GEOMATE. 2021;20(77):173-80.
Federal Emergency Management Agency. FEMA 356/November 2000. Prestandard and commentary for the seismic rehabilitation of buildings. Washington: American Society of Civil Engineers, Federal Emergency Management Agency; 2000.
ACI Committee 318. Building code requirements for structural concrete (ACI 318-19), commentary on building code requirements for structural concrete (ACI 318R-19). Farmington Hills: American Concrete Institute; 2019.
Seong DJ, Kim TH, Oh MS, Shin HM. Inelastic performance of high-strength concrete bridge columns under earthquake loads. J Adv Concr Technol. 2011;9(2):205-20.
Cusson D, Paultre P. Stress-strain model for confined high-strength concrete. J Struct Eng. 1995;121(3):468-77.
Mander JB, Priestley MJN, Park R. Theoretical stress-strain model for confined concrete. J Struct Eng. 1988;114(8):1804-26.
Scott BD, Park R, Priestley MJN. Stress-strain behavior of concrete confined by overlapping hoops at low and high strain rates. ACI J Proc. 1982;79(1):13-27.
Park R, Paulay T. Reinforced concrete structures. New York: John Wiley & Sons; 1975.
Agustiar, Tavio, Raka IGP, Anggraini R. Behavior of concrete columns reinforced and confined by high-strength steel bars. Int J Civ Eng Technol. 2018;9(7):1249-57.
Machmoed SP, Tavio, Raka IGP. Potential of new innovative confinement for square reinforced concrete columns. J Phys: Conf Ser. 2020;1469:012027.
Machmoed SP, Tavio, Raka IGP. Performance of square reinforced concrete columns confined with innovative confining system under axial compression. Int J GEOMATE. 2021;21(85):137-44.
Tavio, Machmoed SP, Raka IGP. Behavior of square RC columns confined with interlocking square spiral under axial compressive loading. Int J Eng Appl. 2022;10(5):322-35.
Pudjisuryadi P, Tavio, Suprobo P. Axial compressive behavior of square concrete columns externally collared by light structural steel angle sections. Int J Appl Eng Res. 2016;11(7):4655-66.
Pinto D, Tavio, Raka IGP. Axial compressive behavior of square concrete columns retrofitted with GFRP straps. Int J Civ Eng Technol. 2019;10(1):2388-400.
Khatulistiani U, Tavio, Raka IGP. Influence of steel bars for external confinement on compressive strength of concrete. Int J GEOMATE. 2021;20(82):146-52.
Honestyo A, Tavio, Ardhyananta H. Axial compressive behavior of bubble-size plastic straw waste FRP-confined circular concrete. Int J Eng Appl. 2023;11(2):73-80.
Mansur MA, Chin MS, Wee TH. Stress-strain relationship of high-strength fiber concrete in compression. J Mater Civ Eng. 1999;11(1):21-9.
Shakya K, Watanabe K, Matsumoto K, Niwa J. Application of steel fibers in beam-column joints of rigid-framed railway bridges to reduce longitudinal and shear rebars. Constr Build Mater. 2012;27(1):482-9.
Eltobgy HH. Structural design of steel fiber reinforced concrete in-filled steel circular columns. Steel Compos Struct. 2013;14(3):267-82.
Sabariman B, Soehardjono A, Wisnumurti, Wibowo A, Tavio. Stress-strain behavior of steel fiber-reinforced concrete cylinders spirally confined with steel bars. Adv Civ Eng. 2018;2018:1-8.
Sabariman B, Soehardjono A, Wisnumurti, Wibowo A, Tavio. Stress-strain model for confined fiber-reinforced concrete under axial compression. Arch Civ Eng. 2020;66(2):119-33.
American Society of Civil Engineerings. ASCE/SEI 41-0.6: Seismic rehabilitation of existing buildings. USA: ASCE; 2007.
Sabariman B, Sofianto MF. Study of crack patterns in the beam column joint due to the upwards anchoring beam effect. AIP Conf Proc. 2017;1855(1):040004.
ACI Committee 374. ACI 374.1-05 (Reapproved 2014): acceptance criteria for moment frames based on structural testing and commentary. Farmington Hills: American Concrete Institute; 2014.
Anggraini R, Tavio, Raka IGP, Agustiar. Stress-strain relationship of high-strength steel (HSS) reinforcing bars. AIP Conf Proc. 2018;1964:020025.
National Standardization Agency of Indonesia. SNI 2052:2017, concrete reinforcing steel. Jakarta: National Standardization Agency (Badan Standardisasi Nasional); 2017. (In Indonesian)
Elwood KJ, Maffei J, Riederer KA, Telleen K. Improving column confinement-part 2: proposed new provisions for the ACI 318 building code. Concr Int. 2009:41-8.
National Standardization Agency of Indonesia. SNI 2847:2019, structural concrete requirements for buildings. Jakarta: National Standardization Agency (Badan Standardisasi Nasional); 2019. (In Indonesian)